China Good quality Double Helical Gear with Free Design Custom

A combination of left-handed and right-handed helical gears with the same twist angle is called a double helical gear. Double helical gears transmit rotational motion between 2 parallel shafts.

Double helical gears have all of the advantages of helical gears, which are strong and quiet, plus have the benefit of canceling the thrust forces by combining helical gears with both right and left-hand twists. On the other hand, they have the disadvantage of being difficult to manufacture.

Double helical gears and herringbone gears are the same types of gear, but those with a groove in the center are called double helical gears, while those without a track where the left and right teeth meet in the center are called herringbone gears.

Advantages of double-helical gears:

  1. Double helical gears are similar to a worm gear, but the teeth are on 2 opposite sides of the gear, which provides a reduction ratio of 1:2.
  2. Double helical gears have very high load capacity and are suitable for heavy-duty applications.
  3. They have a large number of teeth, which helps reduce heat build-up. Hence they can last longer.
  4. They provide an increased reduction ratio in comparison to standard worms gears.
  5. Helical gears can be used with both parallel and non-parallel shafts.
  6. The tooth profile is more efficient than that of a worm gear.
  7. Double helical gears have fewer parts in comparison to worms gears.
  8. They produce low noise.
  9. Double helical gears are better at cutting curves compared to spur gears.
  10. Double helical gears are manufactured using 2 spiral-shaped surfaces on a single gear, making them more robust than the normal ones.
  11. Double helical gears are very smooth at gear operations.
  12. Double helical gears are simple and easy to use, making them economical for most applications.
  13. They are more efficient because they transfer power between the input and output shafts, providing a significant amount of power to the output shaft with less mechanical energy required at the input.
  14. They have a high-efficiency factor that is determined by their ratio, which is often significantly higher than other types of gear teeth (such as spur or bevel).

 

Similarities between single helical gear and double-helical gear

  • Like every gear drive, these 2 are also engagement-type mechanical drives. A chain drive is another example of the same. Though belt drive is 1 mechanical drive, it is 1 friction drive.
  • In both cases, teeth are cut in the form of a helix on the pitch cylinder of the gear blank. The hand of the helix is, however, different in 2 cases.
  • In both, the cases teeth of 2 mating gears come in contact gradually. Thus vibration, noise, and teeth wear rate is reduced substantially compared to spur gear.
  • Both are applicable for transmitting motion and power between parallel shafts only. A bevel gear can send power between intersecting beams, while worm gear can be employed for non-intersecting non-parallel shafts.

Differences between single helical gear and double-helical gear

Single Helical Gear Double Helical Gear
A single helical gear has teeth inclined in any 1 direction (either left-hand helix or right-hand helix). The double-helical gear consists of 2 identical gears jointed on the same axis and teeth in opposite directions (one has a left-hand helix, and the other has a right-hand helix).
Single helical gears develop axial thrust force and exert the same on corresponding bearings. It also generates radial force. The resultant thrust force developed in double helical gear is zero. Thus it exerts no axial load on bearings. But radial force exists as usual.
The power transmission capacity of a single helical gear is comparatively low. Double helical gears can transmit more significant power for exact size and module.
Single helical gears are cheaper. Double helical gears are costlier as design and fabrication are complex and time-consuming.
High precision is usually not desired during the alignment of the gears. Two helical gears must be aligned precisely; otherwise, thrust force will not balance properly, resulting in a negative vibration.
Because of thrust load, a high helix angle cannot be used. Helix angle for single helical gear usually varies from 15º – to 20º. Due to the canceled thrust load, a high helix angle (20º – 45º) can be advantageously used in double helical gears.
The efficiency of single helical gear is comparatively low. Double helical gears can provide higher efficiency.
The bearing span (distance between 2 bearings) is short. The bearing span is longer due to a central relief groove in between 2 gears.
Single helical gears are suitable for mechanical drives or power transmission requirements, where each application usually requires a unique design for powers, speeds, and configuration. Double helical gears are suitable for high power transmission requirements in cranes, marine drives, or turbines.